 |
 |
 |
|
Presenting Dawn, a precision-cut soft bob that embodies sophistication and elegance. With its clean lines and refined silhouette, Dawn offers a timeless allure that effortlessly enhances any look. Designed with low density and minimal permatease, this style achieves a natural, understated beauty that never feels overdone.
Heat Resistant Synthetic Fibers ~ Experience the freedom of heat styling with this advanced synthetic fiber that tolerates high heat, allowing for styling versatility similar to human hair. This fiber has a natural-looking finish with less shine comparted to standard synthetic options, closely replicating the appearance of real hair.
Available in "Renau Exclusive" colors ~ Fashion inspired hues that include Renau Naturals (RN), Ombre, and Shaded colors.
Dawn by Jon Renau - Heat Defiant Collection
HD | Heat
Defiant Care
We recommend washing your alternative
hair every 6-8 wears
CLEANSE & CONDITION
- Before washing, gently remove
any tangles using your wide tooth comb ONLY
- Wet hair completely using cool
running water
- Gently lather the hair with a
small amount of shampoo, making sure that the hair is traveling in the
same direction. DO NOT rub hair; this will cause tangling.
- Rinse thoroughly under cool
running water until water runs clear.
- Wrap wig or hairpiece in a towel
and gently pat dry.
- Gently detangle hair using wide
tooth comb
- Spray with leave-in conditioning
spray (3-5 pumps) keeping away from the base.
DRY & STYLE
- Allow wig or hairpiece to air
dry naturally by placing on a plastic or wire wig stand. DO NOT blow dry.
- Air drying your wig will give
the best results. The fiber will dry fastest; be sure the cap is
completely dry before wearing, storing, or displaying.
- Apply detangling spray (3-5
pumps) focusing on the bottom half of wig or hairpiece. Gently comb
through using your wide tooth comb.
- ONLY a wide tooth comb should be
used on your HD fiber. Other tools will cause frizzing / tangling.
- HD fiber can withstand heat up
to 350 degrees F, however, Jon Renau recommends working at 270 degrees to
280 degrees F.
- It is recommended to use
professional grade heat styling tools with digital temperature settings to
control heat.
CURL & FLAT IRON
- Heat your curling or flat iron
to 270 degrees - 280 degrees F
- Using your wide tooth comb,
gently comb hair free of tangles.
- Starting at the nape, take 1/2
inch to 1.5 inch sections of hair (smaller sections + tighter curls,
larger sections = looser curls)
- Spray thermal heat spray on the
section to protect the fiber (1-2 pumps per section)
~~ CURL
- Gather hair into curling iron,
smooth through to the ends. Roll iron up towards base of wig or hairpiece,
staying 1-2 inches away.
- Hold for 10-15 seconds, then
turn the tip of the iron toward the ground and release curl into palm of
hand
- Holding curl in one hand, gather
up towards base and secure curl with a small metal clip (like a pin curl)
- Allow curl to cool completely
(about 5 minutes); remove clip and let curl hang naturally.
-- FLAT IRON
- Starting at the nape, take 1/2
inch - 1.5 inch sections
- Spray thermal heat spray on the
section to protect the fiber (1-2 pumps per section)
- Slowly smooth flat iron down
through ends; keep hair smooth by following behind the flat iron with your
wide tooth comb
- Allow hair to hang naturally and
cool completely.
TIPS
- All synthetic fibers can tangle
and frizz with wear. It is important that the frizz is corrected early to
avoid permanent damage to the fiber. Use your flat iron to smooth any
frizz before washing
- We recommend using HD detangling
spray with a wide tooth comb DAILY to detangle your HD wig. This is
especially important with the mid-length to long length HD wigs or
hairpieces.
|
|
|
 |
|
 |
|