 |
 |
 |
 |
Whether the dress code is formal or casual, this modern cut pairs just as perfectly with a cocktail dress as it does jeans and a T-shirt. Precise layering adds subtle volume, generous movement and an effortlessly sophisticated look. Special features include a monofilament top, temple-to-temple lace front and heat-friendly Tru2Life fiber.
TRU2LIFE HEAT-FRIENDLY HAIR CARE INSTRUCTIONS
Tru2Life synthetic fiber looks and feels like real hair. The
texture is light, soft and lustrous without being shiny, plus it’s
heat-friendly! Straight styles can be curled and curly styles can be
straightened using your flat iron, curling iron or blow dryer.
Important
- Take
special care with lace front wigs and hairpieces. The lace is delicate and
should not be tugged or pulled.
- Sudden
bursts of heat, such as opening an oven door, may damage heat-friendly
synthetic fiber.
- We do
not recommend sleeping, showering, or swimming while wearing.
- For
longer styles, comb through nape area often using your fingers or a
wide-tooth comb.
- Hair
color cannot be used on synthetic fiber.
Pre-wash
Gently remove tangles using your fingers or a wide-tooth
comb. (Do not use a brush.) Start at the ends and slowly work toward the base
to avoid damage. Do not overstretch or pull on the fiber.
Wash
- Add 1
tbsp of HairUWear CLEANSE to a washbasin of cool water. Caution:
Hot water will damage synthetic fiber.
- Soak
wig or hairpiece in washbasin for 3-5 minutes. Do not scrunch or
agitate. Caution: Soaking longer than 5 minutes can damage the wig
or hairpiece.
- Rinse
under cool running water until the water runs clear. Use a clean,
colorfast towel to gently press out excess water. Do not twist or wring.
- Apply
a light mist of HairUWear RESTORE and comb through using a
wide-tooth comb starting at the ends. Caution: Do not apply
RESTORE directly to hand-tied areas as this may loosen the knots and cause
shedding.
- For
wavy/curly styles, be careful not to overstretch or pull on the fiber.
- The
damp wig can then be placed on a wig stand to dry. Hairpieces
can be clipped on a hanger to dry, however hand-tied hairpieces should
instead dry flat on a colorfast towel to prevent any damage to the
delicate construction. Caution: Do not dry wig on a solid form or
mannequin head to avoid overstretching the cap.
Styling
- Shake
to release fiber. Style with your fingers to achieve the desired look.
- There
are a variety of styling brushes and combs specially designed
for synthetic wigs and hairpieces.
- Tru2Life
fiber can be curled, waved, flat-ironed or blown dry to achieve a
different texture. Once heat-styled, the wig or hairpiece will keep the
new texture even after washing.
- Use a
light mist of HairUWear PROTECT heat-protectant silicone spray
prior to heat-styling.
- Tru2Life
fiber can withstand a low-medium heat setting up to 350°F/180°C. Caution:
Fiber will be damaged if the heat setting is too high. Do not heat-style
while wearing as heat-friendly synthetic fiber will get very hot.
- To
straighten: take a 1-inch section and run a flat iron from the base to the
ends. Allow to cool.
- To
curl: wrap a 1-inch section around a curling iron and hold for 10 seconds.
Carefully slide the iron out and hold the curl shape with a hairpin or
clip until completely cool to set the curl.
- HairUWear
offers medium hold, strong hold and heat-styling sprays specially
formulated for synthetic fiber.
- For
wavy/curly styles, refresh the texture as needed by spritzing with a 50/50
mix of water and RESTORE while finger-styling
Maintenance
- After
each wearing, gently comb through the wig or hairpiece using your fingers
or a wide-tooth comb.
- Use
HairUWear REFRESH neutralizing spray as needed to extend the
time between washings.
- To
avoid unwanted kinks or crimps, store on a wig stand (or clip
hairpiece on a hanger).
- To
maintain wavy/curly textures, style only when the hair is completely dry
using only your fingers. Do not comb or brush dry hair as this can loosen
the texture.
- After
extended wear, matting and frizzing can occur. To detangle and
recondition: wash as recommended, spray with HairUWear RESTORE, then
comb through with a wide-tooth comb starting at the ends.
|
|
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
Specifications
Collection: Signature
Cap Construction: Memory Cap III
- Monofilament Top - gives the illusion of a natural scalp like appearance, allowing you to part the hair in any direction.
- Extended Lace Front Hairline - virtually invisible sheer lace front for a natural looking off the face styling. Lace extends temple to temple.
- Velvet-Lined Ear Tabs
- Velvet-Lined Extended Nape
Cap Size: Average
Hair Type: Tru2Life® Heat Friendly Synthetic Fiber
- can be styled using a flat iron or curling iron, up to 350 degrees.
Hair Lengths:
- Front: 4.5"
- Crown: 6.5"
- Sides: 6"
- Back: 5"
- Nape: 6"
Weight: 3.3 oz (94 grams)
|
|
 |
 |
 |
 |

|